Inlet valve replacement

Inlet valve replacement DEFAULT

How to Repair a Washing Machine Water-Inlet Valve

Materials

  • New water inlet valve (if needed)
  1. Check the Filter Screens

    Check for clogs in the filter screens in the water inlet valve, which can block water flow. This is a common reason the valve may malfunction and the easiest problem to remedy.

    Use a flashlight to look inside each of the two hose fitting ports on the water inlet valve—there should be a screen inside the port. Carefully clean the screens if they are dirty. Be careful not to damage the screens, as they cannot be replaced.

  2. Test the Inlet Valve Solenoids

    If clogged screens are not the problem, test the valve for failure. Depending on the washer model, you may have to remove either the back or front of the washer cabinet to gain access to the wire connections on the water inlet valve.

    Remove the back, top, or front of the cabinet, as appropriate, following directions in the appliance owner's manual. Once you've gained access to the valve, note that two wires are connected to each solenoid; pull them off one at a time and label them so that you can reconnect them correctly.

    Set a multimeter (also called a volt-ohm meter) to the OHM X1 setting and test the solenoids for continuity by touching one tester probe to one of the two terminals on each solenoid. The reading should indicate some resistance. If the reading indicates zero resistance, or infinity (∞), the solenoid is faulty, and the valve must be replaced. Test both solenoids separately; if either is faulty, the entire valve must be replaced.

  3. Replace the Water Inlet Valve (as Needed)

    Unscrew the fasteners securing the valve to its housing or the back of the washer. Note the color and position of the wires attached to the solenoid, and label them. Disconnect the wires by pulling the plugs apart.

    Disconnect the inlet valve from the internal tube (or tubes) that sends water to the tub. This is usually secured with a hose clamp, which you remove with a screwdriver or pliers, depending on the type.

    Write down the brand and model number of the washer and, if you can find it, the brand and part number of the water inlet valve. With that information, obtain a replacement valve from an appliance parts dealer. 

    Install the new valve by reversing the disconnection procedure.

    Tip

    Online appliance parts dealers carry a full selection of parts for appliances of almost any model or age. Shop around for the best prices and shipping rates. The better websites also have video tutorials and other resources for help with making repairs.

Sours: https://www.thespruce.com/repair-washing-machine-water-inlet-valve-1824606

How much does it cost to replace a water inlet valve?

Most common washer repairs and cost to fix:
Water inlet valve issues: $160+

Click to see full answer.


People also ask, how much does a water inlet valve cost?

Only 2 left in stock - order soon. Perfect fit for Kenmore HE3T washer and a good price. The old valve had started leaking and the tub would fill with water over the period of a couple days if you didn't shut it off at the faucet.

Top Selected Products and Reviews.

List Price:$50.82
Price:$19.98
You Save:$30.84 (61%)

Additionally, how much will it cost to repair my washing machine? The national average repair cost for washing machines ranges from $50 to $180, depending on labor costs, the brand of washing machine, the problem the technician needs to fix, and the cost of any replacement parts. A washing machine is a major household appliance.

Subsequently, question is, how much does it cost to replace a washing machine valve inlet?

National statistics are wishy-washy. Some put the average washing machine repair price range at anywhere from $51 to $350, while others (including one of our top competitors) say repairs will run you a minimum of $200.

Is it worth fixing an old washing machine?

If your appliance is still under warranty, you may not have to shell out any cash. Unfortunately, if your washer is out of warranty, it's all on you. One popular take goes like this: If fixing the appliance costs 50 percent or more of the original purchase price then you should replace it [source: Consumer Reports].

Sours: https://askinglot.com/how-much-does-it-cost-to-replace-a-water-inlet-valve
  1. Restoration franchise cost
  2. Custom hotas throttle
  3. Nebraska weather radar

How to Replace Your Washer Water Inlet Valve

The water inlet valve on your washing machine is the gatekeeper for water flow. When the water lines are connected, the inlet valve controls whether water is allowed to flow into the washer during the fill and wash cycles. It is usually located in the back of your washer near the fill hose connections, for obvious reasons. However, when your inlet valve stops working, this can spell real trouble for residents. A failing inlet valve can fail in two different ways. It can stop triggering, blocking water from entering your washing machine entirely, or it can break and cause ongoing flooding from your washer.

In either case, you’ll need to replace your washer’s water inlet valve. We’ll take you through the step-by-step process of replacement.   

These steps are generalized and can vary by the model and brand.

Gather Your Supplies

The first step in any repair is to gather your supplies. It’s important to have your tools and equipment ready so that you can perform the entire repair from beginning to end. Naturally, the most important item is your replacement water inlet valve. Research the correct replacement part number using the make and model of your washer.

  • Screwdriver
  • Channel Lock Pliers
  • Needle-Nose Pliers
  • Work Gloves
  • Towel
  • Bucket

Safety First

The next step is to make sure that your washer is safe to work with. The water inlet valve interacts with both electricity and water, so you’ll want to be extra careful and turn off both the power and water for this repair.

  • Pull Out the Washer
    • Start by pulling your washer away from the wall. This repair will involve accessing the back, so you’ll need room to work. The other two safety steps, disconnecting the power and water, can also be done more easily with the washer pulled out. Use the help of a friend, if necessary, to pull out your washer safely.
  • Shut Off the Power
    • You’ll need to disconnect the power from your washer. With your washer pulled away from the wall, you should be able to reach the plug to pull it out. If you still can’t reach the plug because it’s in an awkward place, switch off the breaker that powers your washer instead.
  • Switch Off the Water
    • Now turn off the water and disconnect the hoses. At the wall, there will be two water supply valves; one for hot and one for cold. Turn these closed and close them firmly. This will prevent flooding while you perform the rest of the repair.

Disconnect the Fill Hoses

  • Visually Designate the Hot-Water Hose
    • Identify the hot water hose on the outside of the washer. If it’s not already visually distinct, apply a piece of red tape or other way to tell which hose is which.
  • Loosen Connections with Channel-Lock Pliers
    • The external fill hoses are connected with a bolt that can be loosened with channel-locking pliers. Loosen these bolts until the hoses can pull free.
  • Disconnect and Pour Out the Hoses
    • Once the connections are loose, pull away from the hoses and point the bottom directly into the bucket. Let the hoses drain to prevent a puddle. Use your towel to mop up any small spills.

Remove the Top Panel

  • Find the Back Mounting Brackets
    • Walk to the back of your washer and look at the top panel. There should be two brackets holding the top panel in place, secured by screws.
  • Unfasten the Mounting Screws
    • Remove those mounting screws securing the brackets and set the screws aside somewhere safe. If the brackets come loose, set them aside with the screws.
  • Slide Top Panel Backward
    • The top panel slides toward the back, away from the front control panel. Grasp both sides, and pull backward. The top panel should come loose.
  • Lift and Set Aside
    • Lift the top panel up away from the washer, then carefully set it aside. Set it on a towel or cardboard to prevent scraping the floor.

Remove the Inlet Valve Assembly

  • Snap a photo of the Wiring
    • Once you identify your water inlet valve, take a close look at the wiring and snap a picture with your phone. This will help you remember how to reattach the wires later.
  • Mark the Hot Water Hose
    • There are two internal water lines connected to the inlet valve, one for hot and one for cold. Snap a photo and/or mark the hot hose line so you can reconnect these correctly.
  • Remove the Wires
    • Carefully remove the wires using needle-nose pliers. Be gentle so as not to accidentally damage the wires as you remove them.
  • Release the Hose Spring Clamps
    • For the two water line hoses, each is connected with a spring clamp. Pinch the spring clamp to release them so that the water lines are loose on the valve.
  • Remove the Hoses from the Valve Assembly
    • With the spring clamps released, pull the water lines away. Have your bucket and towel ready just in case of a small mess.
  • Hold and Remove the Mounting Screws
    • The inlet valve is now only connected by two mounting screws. Hold the valve so it does not fall and remove the two screws. Set the screws aside somewhere safe and discard the old inlet valve.

Install the New Water Valve Assembly

  • Mount with the Mounting Screws
    • Hold the new inlet valve in place and secure with the mounting screws you just removed.
  • Connect the Hoses to the Valve Assembly
    • Slip the hoses back on, being certain they are in the right order. Settle them tightly into place.
  • Secure the Spring Clamps
    • Secure the water line hoses on their mounting points with the spring clamps.
  • Precisely Return the Wires
    • Now reinstall the wires carefully, using your phone as a reference to ensure each wire goes where it’s supposed to.

Reassemble Your Washer

Now it’s time to put your washer back together. We’ll go through this part quickly, as it includes the previous steps done in reverse.

  • Align the Top Panel
  • Slide Into Place
  • Secure the Mounting Screws
  • Return the Fill Hoses
  • Turn On the Water
  • Plug-In the Washer
  • Push the Washer Back Into Place

Test Your Success

Finally, it’s time to test and see if your repair was successful. Run a small load of laundry. If the clothes come out damp and there are no leaks, then your repair was a success. Congratulate yourself and add a notch to your screwdriver handle for another repair well-done.

Sharing

Sours: https://fleetappliance.com/washer-repair/how-to-replace-your-washer-water-inlet-valve/
How To: Whirlpool/KitchenAid/Maytag Water Inlet Valve W10408179

How much does it cost to replace a washing machine water inlet valve?

Ask us anything

The washing machine inlet valve is used to connect the hoses. A faulty inlet valve can cause the tub to only have a small amount of water in it. Replacing a washing machine inlet valve can cost up to $125.

Home-x logo
Limited time offer

Let's Get It Fixed!

Our virtual experts can diagnose your issue (for free!) and resolve simple problems.

Call 1 (855) 466-3948 Call now

RATE

Link copied to
clipboard.

Shop Recommended ProductsShop HomeX Recommended Products

RELATED QUESTIONS

Sours: https://homex.com/_/ask/how-much-does-it-cost-to-replace-a-washing-machine-water-inlet-valve

Replacement inlet valve

At lunchtime I called my parents and asked them to stay with my grandchildren until tomorrow. When asked what happened, she answered the truth that Katya had arrived and we wanted to meet in the evening. At half past five the doorbell rang. - Hi, Olenka. My sister sang from the doorway.

How To Repair Water Inlet Valves on Electrolux \u0026 Wascomat Washing Machines

This is not love. - he muttered, gently stroking her naked body, and I writhed under the window from her confession and from anger at Brockenberg. I tore her up, I thought, I was so rude. Damn, damn, damn.

You will also be interested:

Room 12 In room 12 I was met by a girl who offered to wear a stage costume. The costume consisted of a black corset, stockings, gloves and a short mini-skirt. No underwear was included in the set, and at first I decided to leave mine, but the girl asked me not. To wear underwear.



3878 3879 3880 3881 3882